testpassport 000-232 题库

shijunhua618

Certified Administrator 000-232 试题库由资深IT认证讲师和 Certified Administrator
产品专家结合 PROMETRIC
3 e( m4 M1 T  j, l  v8 I或 VUE
6 k' r9 G, Z7 `/ _. S; e的真实考试环境最新原题倾心打造.最新 testpassport000-232

1.Which command lists out the physical volume names as well as total/free PPs in volume group

datavg?

A.lsdev -Cl datavg

B.lsvpcfg datavg

C.lspv -p datavg

D.lsvg -p datavg

Correct

2.A system administrator needs to configure dump devices for the system. Which command

would be used to estimate the size required for a dump device?

A.lsdev

B.chdev

C.sysdumpdev

D.sysdumpstart

Correct:C

3.Which command restarts the TCP/IP subsystem?

A.refresh -s inetd

B.refresh -s tcpip

C.refresh -g /etc/rc.tcpip

D.refresh -g /etc/inetd.conf

Correct:A

4.Prior to implementing an LPAR system, which of the following needs to be done?

A.A graphics monitor must be attached to the server

B.Cluster System Management (CSM) software must be installed

C.The LPAR system must have an Hardware Management Console (HMC) connected

D.Each LPAR must be configured with a CDROM for operating system installation

Correct:C

5.A system administrator's daily monitoring has revealed a failing disk drive. The drive that is

failing, hdisk0, is a lvm mirrored drive. What is the first step that should be taken in order to

physically replace this drive?

A.Remove the physical volume from the system.

B.Remove the physical volume from the volume group.

C.Remove the physical partitions from the volume group.

D.Remove the logical volume copies from the failing drive.

Correct

6.How would the system administrator turn on Dynamic Processor Deallocation?

A.Use the diag menu to set dynamic deallocation to 'on'

B.Use the chdev command to enable the 'cpuguard' attribute of sys0

C.Use the cfgmgr command to change the 'monitor' attribute of proc0

D.Use the smitty command with the fast path dynamic_processor_deallocation to turn it on

Correct:B

7.A system administrator suspects that there were problems with the AIX installation on a pSeries

server. Which of the following commands can be used, with the appropriate flags, to view the BOS

installation output files?

A.alog

B.errpt

C.lscfg

D.installp

Correct:A

8.The system administrator wants to use a new jfslog /dev/fs1log with the filesystem /test/fs1 on

the testvg volume group. The following commands were used to create the log and assign it to the

filesystem: mklv -t jfslog -y /dev/fs1log testvg 1 chfs -a log=/dev/fs1log /test/fs1 While trying to

mount the /test/fs1 filesystem the administrator received the error "Cannot mount /dev/fs1lv on

/test/fs1: A system call received a parameter that is not valid". What step did the administrator

miss that most likely caused the error?

A.Use the logform command to format /dev/fs1log as a jfslog

B.Use the chlv command to change the lv type of /dev/fs1log to jfslog

C.Use the chvg command to change the default jfslog of testvg to /dev/fs1log

D.Edit the /etc/filesystems file to change the log associated with /test/fs1 to /dev/fs1log

Correct:A

9.A support specialist started to apply an APAR on a system by inserting the tape into the tape

drive, and loaded the fix using smitty installp. The following error message is displayed: tape not

in backup format Which of he following will resolve this problem?

A.Change density setting to 2

B.Set tape device to /dev/rmt0

C.Set block size to 0 for variable

D.Enable compression on tape device

Correct:C

10.A system administrator has filesystems that should not be mounted during system startup.

How can the system administrator prevent the /data filesystem from being mounted during

subsequent boots?

A.mount -no /data

B.chfs -A no /data

C.mount -t nfs /data

D.chfs -a type=nfs /data

Correct:B

有需要的朋友自己下载(PDF格式)